The hollow center also helps it sit flat on uneven surfaces. ![]() I can not tell it from a solid section of log in use. This is a hollow light weight stand that is VERY solid. When this photo was taken for a magazine I had not put the blocks on that keep the anvil in place. This is the style of stand I have been using for 28 years. There are a lot of ways to adapt this design to suit yourself. The tool holding strap could also be a strip of hardwood. To create the right fit you may need an extra "shim" made of plywood so the stack of lumber comes out the proper dimension to fit your anvil. In my drawing I show how to do it if you have an even number of boards and the ends do not come out the same. Steve attached a metal strap to make "pockets" to hold tools. The threaded rod actually clamps the anvil in place. There are no nails or shims and the anvil sits on a bed of silicone caulking (really If you look at the ends of the anvil stand you will notice the 1/2" threaded rods that hold the thing together. I suggest using yellow carpenter's glue and glue coated nails. I'd forgotten that Steve's end boards were 1-1/2" taller than the others to retain the anvil.Įach board is offset about 1-1/2 to 2" as they are stacked up. NOTE: When I was making my drawing below I had not looked at this photo for a year. The unique and HANDY thing about this design is the offset Steve put in the pieces as he stacked them up. ![]() It is a solid section built up by laminating pieces of 2x12 framing lumber. This anvil stand was built by Steve Barringer of B2 Design in Mooresville, NC. There are numerous ways to build an anvil stand. OR have them available when we NEED a stand. Often after wind or ice storms you can have your choice of log sections if you ask and have a way to haul them home.ĭon't forget that a taller section of log is a handy stand for a swage block OR to carve depressions in the end for forming sheet metal.īut, we are not always so lucky to have windfalls of large logs available OR the chain saw to cut to size. The piece of oak was collected after an ice storm. This old German anvil is setting on an oak stump that was trimmed to fit. Most modern smiths prefer some degree of portability. When you do this you want to be VERY sure that you will not want to change your anvil location. In old shops with permanent forge and anvil locations longer sections of logs like this were often set deep in the ground. I prefer to be able to lift mine off the stand if needed. Some smiths strap their anvils down to reduce the ring. Usually there are some spikes driven in the stump to keep the anvil from walking off from vibration. This is a short section of log that sets on the ground and the anvil sets on top. The Peter Wright anvil on a red oak stand at top is a classic. It really shows the resourcefulness of our forefathers and foremothers to utilize what we have at hand to construct a tool that is needed in our everyday lives.Ĭreate an account or login in order to post a comment.August 14, 2002, Appended 8/16, 9/7, 10/20, 2005 (updated may 28, 2011) ![]() I really enjoy seeing repurposed items into useful tool. It would make sense that RR shops made these. I honestly don't have any clue about how it was made, only guessing that maybe the original craftsman had access to an actual RxR machine shop or something.? I *do* know that RxR iron, generally, is much harder steel than most other varieties.this piece is even more curious showing its various remaining evidence of whatever tools/machines were used to make it. WOW, what a response! :-) :-) :-) THANKS SO MUCH to EJW-54, fortapache, jscott0363, yougottahavestuff, Watchsearcher, ho2cultcha, Irishcollector., buckethead, Brunswick, Ben, Anik, iggy, blunderbuss2, bobby725, officialfuel, & Rageunder for stopping by and sharing the s for my old track anvil!!īB2, I certainly agree that someone with some good skills (plus some really good tools otherwise?!) made the thing.?! I had a piece of rail I used as an anvil once. Lot of good work when into making that one.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |